S&F STEAD & FAST Annular Cutter Set 6 Pcs, Diameter 1/2 to 1-1/16", DOC 2"
- INDUSTRIAL-GRADE M2AL HSS ANNULAR CUTTERS – Made with super tough M2AL high speed steel (HSS) for durability, wear resistance, heat resistance and long service life. Built for professional metalworking users who need sharp cutting performance and reliable drilling efficiency.
- FASTER DRILLING WITH CLEAN HOLE FINISH – CNC-machined annular cutters cut faster than standard drill bits by removing only the hole edge instead of the entire hole area. Our core drill is designed to produce smooth, reamed, burr-free holes with minimal deformation and improved edge finish.
- 6 STANDARD SIZES WITH 2” DOC – HSS annular cutter assortment includes 6 core drill bits with outside diameter: 7/16”, 9/16”, 11/16”, 13/16”, 15/16”, 1-1/16”. Each annular drill cutter has a 2 inch cutting depth for deeper metal drilling applications.
- SECURE 3/4” WELDON SHANK FIT – 3/4 inch Weldon shank with 2 flats provides secure clamping, reduced vibration and stable cutting performance. Compatible with major magnetic drill brands including Alfra, BDS, Champion, Dewalt, Evolution, Fein, Euroboor, Hougen, Milwaukee and Ruko.
- ORGANIZED KIT IN STURDY STORAGE CASE – Annular drill bit set includes 6 annular cutters, 2 pilot pins, 1 hex wrench and a sturdy plastic carrying case for organized storage, protection and transport.
- CAUTION – Annular bits are for single-layer drilling only. Secure the workpiece firmly, and start with a low feed rate before increasing once the cutter is 2-3mm into the material. Drill press use requires an additional annular cutter arbor, which is not included.
Estimated shipping
Select a product to estimate shipping.CNC-machined high precision cutters with 3/4 inch Weldon shank
Made with high quality HSS (High Speed Steel)
For fast cutting of burr-free holes in metal sheets – no pre-drilling or step drilling required
Cut to tight tolerances
Long-lasting drill bit cutting tool; can be re-sharpened
Suitable for many metals including stainless steel, carbon steel, aluminum, cast iron, cast copper
Annular Cutter Teeth Detail
Teeth with multi-cut geometry for improved ply cutting and chip removal
Weldon Shank
3/4 inch Weldon shank
2 flat faces for secure clamping
Pilot Pin
Marks the center of the hole to be cut
Allows the easier flow of lubricant
Ejects the slug out of the metal
Hex Wrench
For tightening the hex screw in the magnetic drill
MAXIMIZE LIFE OF YOUR ANNULAR CUTTER / PREVENT PREMATURE DULLING OF BLADES
Use our HSS annular cutters to cut suitable materials only
Drill single layers of materials only. This series of annular cutter is designed for single layer drilling only.
Recommended for steel sections and steel plate. Can also be used for the materials listed above.
For hardened metals, use carbide annular cutters, also available in our store.
Secure workpiece firmly before drilling
There should be no movement between the workpiece and drill during cutting.
If using a magnetic drill, check there are no metal chips on the magnet base before each cut. They will prevent full magnetic adhesion with the workpiece.
If the workpiece is less than 1/2” thick, use a 3/8” steel sheet under it to ensure the magnetic drill will grip it firmly.
Ensure the correct rpm is used
Consult the above table to use the correct rpm where possible.
Use a low feed rate when engaging the annular cutter with the work piece, especially for the smaller bits.
Once the cutter is about 2-3mm in, the feed rate can be increased to the recommended rate.
Match the annular cutter size and material drilled to the correct feed rate
Recommended speed at which holes should be cut in mm/min = * Feed rate F x **Rotation Speed R
As an illustration, using an annular cutter size 1⁄2” to drill holes in low carbon steel, the speed at which the hole is cut should be between 0.08 x 612 = 49 mm/min and 0.13 x 612 = 80 mm/min. Adjust the rotation speed of the feed handle to match the recommended speed.
Product details
Specifications
| Main Specification | |
|---|---|
| Manufacturer | S&F STEAD & FAST |
| Unit Count | 1 Count |
| Surface Recommendation | Alloy Steel |
| Cutting Diameter | 2 Inches |
| Shank Type | Weldon |
| Tool Flute Type | Spiral |
| Brand | S&F Stead & Fast |
| Number of Pieces | 6 |
| Material | High Speed Steel (Hss) |
| Finish Type | Uncoated |
| Global Trade Identification Number | 05060917980197 |
| Product information | |
|---|---|
| Set Name | Annular Cutter Set |
| Technical Details | |
|---|---|
| Part Number | ZXT-HAZ-016 |
| Model | ZXT-HAZ-016 |
| Material Type | High Speed Steel (HSS) |
| Number of Flutes | 3 |
| Style | |
|---|---|
| Finish Types | Uncoated |
| Others | |
|---|---|
| Item Highlight | Professional Grade, CNC-Machined, 3/4" Weldon Shank, 2 Pilot Pins, M2AL HSS Mag Drill Bits Kit for Magnetic Drill Press |
| Product Type | Annular Cutters |
| Tags | |
|---|---|
| Tags | |