ELEGRP Lighted 20 Amp 125 Volt NEMA 5-20P 2 Pole 3 Wire Grounding Straight Blade Electrical Plug Replacement Cord Outlet Commercial Grade, Yellow, 5 Pack
- 【Good to Use and Install】 Unique dimpled body provides a secure gripping, turning and pulling. Face and body feature alignment make it easy to assemble. Grip screws are installed from the same side to make tightening easy.
- 【Adjustable Wiring Gauge】 ELEGRP extension cord replacement ends with an adjustable rear cord clamp for various wires sizes 18-12 AWG, and it is suitable for making new power cables, or repairing extension cords. Good for industry, home, office, garden, etc.
- 【Wide Application】 Perfectly for use with Generator Transfer Switches or Power Inlet Plug to supply power to your Home, Business, Marine/Boat or RV/Trailer. Widely used for Generators, welding equipment, Sump & Well Pumps.
- 【Toughened Construction + Copper Brass Connectors】 Insulated and solid housing will keep non-current carrying parts from becoming energized and won’t crack in high abuse applications. Formed from a single piece of solid brass to reduce friction and overheating, providing excellent conductivity.
- 【Green Neon Light】 Green neon light indicates that power is flowing.
Estimated shipping
Select a product to estimate shipping.Wide Application: Perfectly for use with Generator Transfer Switches or Power Inlet Plug to supply power to your Home, Business, Marine/Boat or RV/Trailer.
Good to Use and Install: Ergonomic fluted body design with circular dent is ideal for gripping, turning and pulling. Face and body feature alignment make it easy to assemble. Grip screws are installed from the same side to make tightening easy.
Loosen assembly screws in face and separate device. If needed, back out cord clamp screws enough to allow the cord to fit between the two clamp halves. Insert cord through cord clamp and housing. Simply remove the minimum cord clamp if the cord dia. is 0.391"-0.655".
Strip cord jacket between 7/8” and 1” from cord’s end. Remove insulation exposing between 3/8” and 1/2” bare copper wire (see diagram 1a). Twist wire strands tightly together. Trim off cord fillers, if any.
Insert bare copper wire into wire clamp and tighten each terminal screw 10-12 in-lbs. torque. Ensure insulation clears clamp; HOT conductor to BRASS terminal, NEUTRAL conductor to SILVER terminal, and GROUND conductor to GREEN hex screw.
Assemble wired device body with housing. Align keyed housing with a key on the device’s body. Tighten assembly screws.
Alternately tighten cord clamp screws 10-12 in-lbs. torque. Ensure cord clamp rests over cord jacket, not over conductors.
Note:
Built-in cord grip adjusts automatically for use with 18-12 AWG.
Product details
Especificaciones
| Main Specification | |
|---|---|
| Fabricantes | ELEGRP |
| Cuenta de unidad | 5 Conde |
| Medida de especificación | Nema |
| Amperaje | 20 A |
| Marca | Elegrp |
| Número de cables | 3 |
| Número de artículos | 5 |
| Componentes incluidos | NO |
| Color | Amarillo |
| Tipo de conector | Plug-In |
| Product information | |
|---|---|
| Número de paquetes | 5 |
| Technical Details | |
|---|---|
| Número de la parte | 4536L-YE5 |
| Número de polacos | 2 |
| Otros | |
|---|---|
| Tipo de producto | Plugs |
| Tipo de plug | NEMA 5-20P |
| Número de alambres | 3 |
| Etiquetas | |
|---|---|
| Etiquetas | |