2Pcs W5500 Ethernet Network Module SPI Interface Full Hardware TCP/IP Protocol 3.3V 5V W5500 STM32 Microcontroller Ethernet Network for Arduino
- W5500 ethernet network module integration hardware TCP/IP protocol; Internal 32K byte memory as TX/RX cache; Support 10/100Mbps transmission rate; Support 8 independent ports to run at the same time
- Support 3.3V or 5V power supply, 5V power supply can also output 3.3V power supply, convenient for users to use in different single chip microcomputer systems; The communication mode between the module and the single chip system is simple and convenient SPI communication.
- Supports hardware TCP/IP protocols: TCP, UDP, ICMP, IGMP, IPv4, ARP, IGMP, PPPoE and Ethernet
- SPI (Serial Peripheral Interface) provides an interface for easy connection with external MCU. W5500 supports SPI interface communication up to 80MHZ
- W5500 provides network wake-up and sleep modes, effectively low system power consumption
Estimated shipping
Select a product to estimate shipping.W5500 chip is an embedded Ethernet controller using all-hardware TCP/IP protocol stack, which enables embedded systems to easily connect to the network through SPI (Serial Peripheral Interface) interface.
W5500 is composed of the integration of all hardware TCP/IP protocol stack, Ethernet network layer and physical layer. Its full hardware TCP/IP protocol stack supports TCP, UDP, IPv4, ICMP, ARP, IGMP and PPPoE protocols. The W5500 uses a 32KB cache as its data communication memory. By using W5500, users can implement Ethernet applications by using a simple socket program instead of dealing with a complex Ethernet controller.
SPI (Serial Peripheral Interface) provides an interface for easy connection with external MCU. W5500 supports communication between SPI interfaces up to 80MHZ. In order to reduce the consumption of system power, W5500 provides network wake-up and sleep modes. W5500 will wake up when it receives a magic packet in the form of a raw Ethernet packet.
Supports hardware TCP/IP protocols: TCP, UDP, ICMP, IGMP, IPv4, ARP, IGMP, PPPoE and Ethernet
Supports 8 independent ports
Provide sleep mode
Provide network wake-up
Supports high-speed SPI bus (SPI mode 0,3)
Internal 32K byte memory as TX/RX cache
Embedded 10/100Mbps Ethernet Physical Layer
Support automatic negotiation (10/100-Based full duplex/half duplex)
IP segmentation is not supported
3.3V working voltage, I/O port can withstand 5V voltage
Multiple indicator signal output (full duplex/half duplex mode, network connection and network speed)
Module pin arrangement function:
3.3V:3.3V power input pin.
5V:5V power input pin
MISO:SPI host input slave output pin
GND: Power ground pin
MOSI:SPI Host Output Slave Input Pin
RST:W5500 Hardware Initialization Pin (Active Low)
SCS:SPI SLAVE select pin (active low)
INT:W5500 interrupt pin (active low)
SCLK:SPI clock pin
NC: hanging
Especificaciones
| Main Specification | |
|---|---|
| Fabricantes | JESSINIE |
| Cuenta de unidad | 2.0 Cuenta |
| Marca | JESSINIE |
| Número de artículos | 2 |
| Dispositivos compatibles | Arduino |
| Peso del artículo | 0,03 Kilogramas |
| Product information | |
|---|---|
| Número de paquetes | 2 |
| Interfaz de hardware | Ethernet |
| Technical Details | |
|---|---|
| Tasa de transferencia de datos | 100 Megabits Por Second |
| País de origen | USA |
| Otros | |
|---|---|
| Tipo de producto | Tarjetas de interfaz de red |
| Unidad de peso del objeto | 0,03 Kilogramas |
| Cantidad | 2.0 Cuenta |
| Protocolo de enlace de datos | Ethernet |
| Etiquetas | |
|---|---|
| Etiquetas | |