5% Cobalt Hss Drill Bits Set (1/4" x 5PCS) for Stainless Steel and Hard Metal
- Premium 5% Cobalt Steel ,66-69 HRC (Rockwell Hardness Scale) ,Usually Give the Best Heat,Wear and Chip Resistance and Long Tool Life.
- Grinding the Cutting Edge Three Times,with the High HRC and Heat Resistance of the Material,Desigh for Cutting through Stainless Steel ,Hardened Steel, Iron Plate, Aluminum,Ducts,Wood,PVC and Plastic.
- This Cobalt Drill Bit is Typically Capable of Running Two to Three Times Faster.Despite the Higher Price,the Cost Per Hole When Using Cobalt Drill Bit Will be the Lowest,Since It Can Produce So Many More Holes.
- The Sufficiently Sharp Bit Edge Can Cut the Metal Material into Long Strips of Iron Chips rather than Slowly Grinding Throng the Material with a Blunt Drill Bit.
- 135 Degree Cobalt Jobber High Speed Steel Drill Bits Set Includes :1/4" x 5pcs (3-flat Shank).
Estimated shipping
Select a product to estimate shipping.Why choose STROTON cobalt drill bits?
The research shows that HSS with cobalt has a higher temperature resistance and Red hardness, a greater wear resistance(Hardness) and a higher heat treat response than HSS without cobalt .
Red hardness, it causes the hardened steel to have an ability to maintain hardness at approximately 860-880 °C .
66-69 HRC,it means that the drill bits has 3X cutting ability and 3X durability.
This drill bits set is made of Premium Cobalt (80,000 dollars per ton).
This drill bits set definitely have more cobalt in them than the "Cobalt" bits that HF sells--which are just Cobalt coated or only a tiny amount of cobalt tipped.
Compared with ordinary high speed steel, 5% cobalt provides better heat and wear resistance,and Hold up Better.
Split Point design tip starts drilling immediately with less force and eliminates "walking" across the work surface.
Ideal for Stainless steel,Hardened Steel,Cast Iron,Aluminum,Copper,Plastic and Hardwood.
The drill bit can be used for mechanical maintenance, such as drilling out bolts and screws.
Non-vertical use may cause the drill bit to break.
Using a drill press with sufficient power will make drilling easier.
Too high speed may burn the bit tip.
Drill bits diameter:
1/16≤3/16,RPM(1000~700)
3/16-3/8, RPM(700~350)
3/8-1/2, RPM(350~200)
Add Cutting Fluid or engine oil to prevent the stainless steel from overheating.
It also works adding some vinegar, soy sauce or water.
The drilling shall be started slowly by applying force slowly and gently until the drill bit starts chipping.
Product details
Especificaciones
| Main Specification | |
|---|---|
| Recomendación sobre la superficie | Madera, Acero, Metal, Plástico, Iron, Acero inoxidable, Aluminio, Pvc |
| Material | Acero de alta velocidad (HSS), Cobalto |
| Fabricantes | STROTON Ltd |
| Cuenta de unidad | 5 Conde |
| Diámetro de corte | 6.35 milímetros |
| Estilo de punto | Taper Point |
| Tipo de Shank | Derecho |
| Tipo de fluido de la herramienta | Spiral |
| Marca | STROTON |
| UPC | 643459994997 |
| Cortar la cuerda del ángulo | 135 grados |
| Número de piezas | 5 |
| Tipo de acabado | Uncoated |
| Product information | |
|---|---|
| Número de paquetes | 1 |
| Nombre | STROTON 5-Piece Cobalt HSS Drill Bit Set |
| Technical Details | |
|---|---|
| Tipo de material | Acero de alta velocidad (HSS), Cobalto |
| Número de la parte | Cobalt 6 series bits inch |
| Modelo | Cobalt6series |
| Número de fluidos | 3 |
| Style | |
|---|---|
| Tipos de acabado | Uncoated |
| Otros | |
|---|---|
| Tipo de producto | Bites de perforación de Jobber |
| Diámetro mínimo de bore | 0,25 pulgadas |
| Etiquetas | |
|---|---|
| Etiquetas | |